What is the core equipment of the license plate recognition parking system ? With the development of technology, the parking lot system is constantly being upgraded and its functions are becoming more and more. At present, the parking lot systems on the market mainly include the following types: IC, ID swipe card, Bluetooth remote card reader, license plate Identify parking system etc. In the past two years, from one experience of people, the license plate recognition parking system is one of the most popular smart parking management systems for car owners.
One of the reasons why the license plate recognition car park system is so popular is that it speeds up people's access to and from the car park. Because of its special function, it is currently used by people in parking lots of various sizes. Then, when choosing a license plate recognition car park system, which aspects should be considered? What are its core equipment?
The license plate recognition parking system and the general parking system are roughly the same in composition, but the license plate recognition parking system will require higher equipment.
First of all, one of the most important factors in the license plate recognition system is the recognition rate. Some people judge the quality of the equipment from the level of the recognition rate. In fact, this is a very unscientific method. The recognition rate is not only related to the problem of the device itself, but also related to the environment of the parking lot. The influence of the environment on the recognition rate may sometimes exceed the factors of the device itself. Therefore, to solve this problem, the license plate recognition parking lot must not only be equipped with high-definition license plate recognition. The camera, but also according to the site conditions to install some light-up equipment to increase its recognition.
Secondly, the most important feature of the license plate recognition car park system is the fast speed of travel. Therefore, compared with the parking lot system for swiping cards, the barricade must use the fast intelligent barricade, and the fast barricade will require the movement of the barricade. Higher, its stability is stronger.
The above is the core equipment in the license plate recognition parking system. Choosing a good parking system configuration can not only prolong the service life of the parking system, but also increase the income of the parking lot and alleviate people's parking problems.
At present, as parking problems continue to spread, the parking industry is increasingly sought after, and parking management systems are also moving from product competition to brand competition to market competition. For enterprises, facing such fierce competition, in order to survive, they must master their own core technologies. The performance of the parking lot system must be excellent. Of course, in order to gain a share in this industry, user experience is indispensable.
For the safety and convenience of parking, many property selections not only examine the strength of the manufacturer of the equipment, but also focus on the function and quality of the product, because this is also an important factor that affects the service life of the parking system. If you cannot choose the parking system that is suitable for your use according to the situation on the site, serious management problems will arise after installation. When the traffic volume is large, the entrance and exit will cause serious congestion problems, and some devices do not support offline use. Therefore, when the parking lot is powered off or the equipment fails, the entire parking system will collapse, giving parking lots. Management caused serious problems.
With the continuous improvement of people's living standards, parking lot equipment companies need to spend more time and effort to design the appearance of products and develop new and more advanced functions in order to meet the requirements of users. In addition, the current parking system hardware equipment is basically the same in terms of working principle, manufacturers need to start from the software to improve, around the owner to have a better parking experience to develop.
Nowadays, many high-tech technologies are gradually integrated into people's lives. Parking companies are also relying on high technology to gradually develop new features. One of its distinguishing features is that they can be unattended and can be enjoyed by car owners and car park managers. Happy parking and management. At present, there are already many parking lots that have already achieved such a function. At the same time, the use of Internet functions enables real-time sharing of parking data, allowing owners and car park managers to be able to understand the use of parking spaces in the parking lot for the first time. A parking space can be stopped to ease congestion.
For the parking industry to survive in this wave of market, it must win the follow-up long-term development with brand strength and good user experience, further improve its own product quality, provide perfect service, which is the core of all parking companies' future development.
Die casting is a Aluminium or Zinc metal casting process that is characterized by forcing nolten metal under high pressure into a die mold cavity. The mold cavity is created using two hardened tool steel dies which have been machined into shape and work similarly to an injection mould during the process. Most die castings are made from non-ferrous metals, specifically zinc, copper, aluminium, magnesium, lead, pewter, and tin-based alloys. Depending on the type of metal being cast, a hot- or cold-chamber machine is used.
The casting equipment and the metal dies represent large capital costs and this tends to limit the process to high-volume production. Manufacture of parts using die casting is relatively simple, involving only four main steps, which keeps the incremental cost per item low. It is especially suited for a large quantity of small- to medium-sized castings, which is why die casting produces more castings than any other casting process. Die castings are characterized by a very good surface finish (by casting standards) and dimensional consistency.
Die Casting Mould,Pressure Washer Aluminium Die Casting,Power Tools Aluminium Die Casting Mould,Filter Rear Cover Die Casting Mould
Zhejiang Ceeto Molding Technology Co.,Ltd. , https://www.ceetomold.com