Pneumatic membrane valve in the soda ash industry is extremely common, supporting the use of other instruments, enabling the production process flow, level, pressure, temperature and other process parameters and other media such as liquid, gas, steam and other automatic adjustment and remote control . With the gradual improvement of the degree of automation of enterprises, the application of distributed control system (DCS) and other smart meters in the field of automation has become more and more common. Through the optimized control of computers, the production will get the most benefit. In the optimization, the main faults of the control system are also concentrated on the regulating valve which is the terminal executing device of the regulating system. The regulating valve receives the control operation signal during the control of the fluid flow and regulates the flow rate according to the control law. Its action or not, is directly related to the quality of the entire control system. According to the control system in the soda ash industry statistics, about 80% of the fault control system from the control valve. Therefore, how to ensure the pneumatic diaphragm valve in our factory production of reliable and accurate operation, we need to explore is a very important issue. Survey of the status quo I plant a total of 237 sets of pneumatic diaphragm control valve, especially in the heart of the plant heavy alkali plant is widely used, of which carbonized three gas flow control all use pneumatic diaphragm valve. Soda ash in the production process, due to the serious corrosion of ammonia salt, ammonium bicarbonate in the following 25 degrees Celsius easy to crystallize the nature of the valve in the operation because of the body wall scarring, crystallization, scaling lead to the valve card, not Action or slow action, the system can not be automatic adjustment of the phenomenon is more common, accounting for 50% of the total number of valve failure, resulting in greater impact on production; by the valve aging filler, hardening valve slow or from the valve stem Leakage and other failures up to 15%; due to the diaphragm damage caused by leakage or hard core fragmentation valve can not be adjusted up to 12% of the phenomenon; due to locators, valves, actuators and other corrosive valve failure caused by the phenomenon of 10%; other Cause the probability of valve failure accounted for 13%. 2 fault analysis based on years of soda ash production site using pneumatic diaphragm valve failure analysis can be summarized as a common fault and its causes are as follows: 2.1 valve does not move 1) due to the regulator Fault, so that no signal conditioning valve. 2) Leakage of air source manifold, so that the valve positioner no source or lack of air pressure. 3) Locator bellows leak, the locator no air source output. 4) Regulating valve diaphragm is damaged. 5) As the constant orifice of the amplifier in the positioner is blocked, the compressed air is water-filled and accumulates at the globe valve of the amplifier, causing the positioner to have a source of air but no output. 6) Due to the following problems, the control valve has a signal but a gas source, but the valve still does not work: (1) the valve core and the bushing or valve seat are stuck; (2) the valve core is off (the pin is broken); the valve stem is bent or broken ; ④ actuator failure: ⑤ reactive type seal ring leaks; ⑥ foreign body block valve. 2.2 valve instability 1) due to the filter valve failure, the pressure of the air supply often changes. 2) Locator amplifier ball valve by the particles or garbage wear, the ball valve is not strict, the air consumption will increase when the output oscillation. 3) Locator amplifier nozzle baffle is not parallel, the baffle cover nozzle. 4) Output pipeline leakage. 5) The actuator stiffness is too small, the thrust of the fluid pressure changes caused by insufficient. 6) stem wear power. 7) pipeline oscillation or vibrations around. 2.3 the valve slow action 1) the reciprocating stroke of the stem is slow: ①the body of mud or viscous media, so that the valve plugging or scaling; ② polytetrafluoroethylene filler hardening, or graphite asbestos packing oil It is dry. 2) Stem unilateral action slow action: ①diaphragm leakage and damage; ② actuator "O" ring leak. 2.4 full closure of the valve when the leak 1) spool corrosion, wear. 2) The outer thread of the valve seat is corroded. 2.5 valve can not reach the fully closed position 1) media pressure is large, the actuator stiffness is too small. 2) there is a foreign body in the valve. 3) Bushing burned. 2.6 Filler parts and the valve seal part of the leakage 1) filler cap did not compress, did not flatten. 2) Dry the graphite asbestos packing oil. 3) PTFE as a filler, PTFE aging deterioration. 4) The gasket is corroded. 3 to establish the valve pre-inspection mechanism In the daily production process, the maintenance of the control valve is only limited to the failure of the valve, rarely carry out regular adjustment and regular maintenance, in the enterprise's measurement management practices is not strict Requirements, in fact, the valve failure stems from the accumulation of a number of unstable factors, the accumulation of a certain extent, the formation of failure, therefore, before the failure of the valve to put these instability factors in the bud, not only can extend the use of the valve Life, but also to avoid the valve failure to produce serious impact. This requires the establishment of valve pre-inspection mechanism or regular maintenance mechanism. Taking the heavy gas-carbonized three-position gas flow control valve as an example, before the pre-inspection mechanism was established, due to the characteristics of easy crystallization, easy scaling and scarring in the soda ash process medium, the resistance of the movable part of the valve body increases, causing the actuator to move Inflexible, sluggish until the control valve spool and bushing or seat stuck can not move after the problem occurs, on the one hand need to stop the tower to disassemble the valve overhaul, affecting the production is inevitable, on the one hand need to prepare spare parts, Spare parts can not find temporary spare parts to take emergency measures have occurred, resulting in failure can not be completely resolved. After the establishment of pre-inspection mechanism, you can have sufficient time to prepare spare parts, spare parts, and valves can be fully under the maintenance of the valve, thereby improving valve performance and service life. 4 Conclusion Through the establishment of pre-inspection mechanism, not only can increase the life of the control valve to reduce valve failure and reduce the failure rate of the instrument, but also to stabilize production, reduce costs and improve efficiency play a positive role in promoting, but also can Optimize the process operation to ensure the long-term stable operation of the production plant.
Medical Masks,Medical Disposable Face Masks,Blue Face Mask,Medical Non-Woven Face Mask
Jiangyin Huashi Medical Equipment Co.,Ltd , https://www.medicalwellcare.com