If the gearbox oil is too little oil leakage or the oil is exhausted, the ratio of gasoline to oil is too large, and the lubrication is not good, which is a factor that causes the engine temperature to be high. If the engine temperature is too low, the pilot should be softened to prevent the air from stopping. It is strictly forbidden to pull the ignition charge during flight. The wire should be inspected regularly to prevent corrosion or aging. The spark plug should be inspected every flight hour, and the spark plug should be replaced once every hour. In particular, a single spark plug is used in an engine, which should be noted. The aircraft must have full-time maintenance personnel. Some air station maintenance is done by the pilot, the flight quality is difficult to guarantee, and the safety flight has hidden hidden dangers.
Maintenance personnel are important factors to ensure flight safety and cannot be ignored or omitted. If the engine is parked in the air, it should immediately maneuver the aircraft to slide down and maintain the speed of the bee-type aircraft, and make a forced landing according to the position and flight height of the aircraft. The order of the forced landing of the off-site is more than 50. The forced landing is carried out. () l Turn the aircraft into a downturn, ensure that the speed is selected as soon as possible, and the landing area is flat and the flight commander is reported. In order to judge the wind direction, the slip route is determined according to the height of the aircraft. Visual inspection should normally be a little higher, closing the oil circuit and ignition switch before landing.
The enclosed cockpit should open the canopy. The landing pull height can be slightly higher, and the aircraft is grounded at a slightly larger elevation angle and a smaller speed. When the plane is about to be grounded, the two feet are quickly retracted, the left arm protects the face, and the steering column is pressed to one side. After grounding, quickly get out of the plane, try to protect the aircraft, and report the situation to the superior in time. The height is below the forced landing (l) immediately turns to the down protection rate) to determine the situation in front of the venue. Usually, it should be forced to make a straight line. If there are obstacles, the direction of the landing should be changed in time, but the turning angle is not too large. Land and grounding movements are the same as those with a height of 50 meters or more.
Advertising cnc router
- UTECH CNC take great pride in manufacturing the most user-friendly, high quality, economical advanced CNC Routers.
- UTECH Advertising CNC Router adopt overall steel body, Linear Guide Rails and Ball screws, it provides long lifetime, superior cutting and engraving quality, while requiring minimal maintenance.
- UTECH CNC Routers are easy to learn and operate, the control system of CNC Router is compatible with Type3/Artcam/UG/Pro-E/Mastercam/Ucancam V9 and so on.
Just for the perfect experience. Strength represents everything.
1.Side hanging structure, 20 square rail and precision ball screw transmission mode, with high precision and efficiency, operate steadily.
2.The structure of the whole machine adopts gantry movable column structure design, full range of precision machining parts and precision assembly, maintain machine's high performance and stability.
3.Control system fully open port, powerful compatibility seamless docking with various software.
4.Suitable for multi-industry accurate customer groups, comprehensive, delicate and easy to learn.
Performance Characteristics:
B. The drive uses a premium brand drive, which is nearly 2 meters faster than the original model.
C. Imported square guide rail, self-lubricating block, make all directions force equal, guaranteed mechanical precision and strength.
D. Use the memory method of the breakpoint to ensure that it can be processed in an accident (broken knife) or in the next day.
E. Gantry type movement, strengthen mesa, strong and durable, long time use not deformation, make positioning accuracy more accurate.(optional)
F. The label making not only makes the engraving fine and not serrated, the bottom surface is smooth and smooth contour, and the cutting of 2 cm organic glass is also easy.
G. The whole process of thickening casting bed, three-axis dustproof system, high power stepping motor.
H. This machine is very suitable for application in small mould, stamping die, motor, micro injection mold, shoe mold, badges, embossing mold, bread, cake, abrasive, biscuit, chocolate, candy mold, art sculpture, dial, font, font, all kinds of marks, trademarks or other processing.
Machine's parameters:
Number
Discription
Parameter
1
X,Y,Z Working Area
600x900x100mm
2
Table Size
720X1140mm
3
X,Y,Z Traveling Positioning Accuracy
±0.01/300mm
4
X,Y,Z repositioning Positioning Accuracy
±0.01mm
5
Table Surface
T-slot table
6
Frame
Steel structure
7
X, Z Structure
Ball Screw
8
Y Structure
PMT Rail Linear Bearings and Ball Screw
9
Max. power Consumption
0.8Kw(without spindle)
10
Max.Rapid Travel Rate
8000mm/min
11
Max.Working Speed
5000mm/min
12
Spindle Power Motor
1.5KW water cooling spindle
13
Spindle Speed
0-18000RPM
14
Drive Motors
Stepper system
15
Working Voltage
AC220V/50/60Hz
16
Command Language
G code
17
Operating System
Nc-studio System (Mach3/DSPSoftware)
18
Interface
USB
19
Flash Memory
128M(U Disk)
20
Collet
ER11
21
X,Y Resolution
<0.01mm
22
Software Compatability
Artcam software, JDPaint software,( 1513427,Option: Ucancam/Type3 software)
Advertising Cnc Router,CNC Wood Working Router,Metal Advertising Router Machine,Mini Advertising Cnc Routers
Shandong U-May CNC Technology Co., Ltd. , https://www.fiberlasers.de